Free Sharing Lead2pass Exam Dumps

Free Download All The Latest Cisco, Microsoft, CompTIA, Oracle, VCP, CISSP Questions And Answers

[PDF&VCE] Lead2pass Provides Free 200-125 Exam Dumps PDF (21-40)

2016 September Cisco Official New Released 200-125 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

Good news, Lead2pass has updated the 200-125 exam dumps. With all the questions and answers in your hands, you will pass the Cisco 200-125 exam easily.

Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/200-125.html

QUESTION 21
Which two protocols are used by bridges and/or switches to prevent loops in a layer 2 network? (Choose two.)

A.    802.1d
B.    VTP
C.    802.1q
D.    STP
E.    SAP

Answer: AD
Explanation:
This question is to examine the STP protocol.
STP (802.1d) is used to prevent Layer 2 loops.
802.1q is a Frame Relay protocol which belongs to VLAN.
SAP is a concept of the OSI model.

QUESTION 22
Which switch would STP choose to become the root bridge in the selection process?

A.    32768: 11-22-33-44-55-66
B.    32768: 22-33-44-55-66-77
C.    32769: 11-22-33-44-55-65
D.    32769: 22-33-44-55-66-78

Answer: A

QUESTION 23
A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?

A.    More collision domains will be created.
B.    IP address utilization will be more efficient.
C.    More bandwidth will be required than was needed previously.
D.    An additional broadcast domain will be created.

Answer: D
Explanation:
Each VLAN creates its own broadcast domain. Since this is a full duplex switch, each port is a separate collision domain.

QUESTION 24
What are three benefits of implementing VLANs? (Choose three.)

A.    A higher level of network security can be reached by separating sensitive data traffic from other
network traffic.
B.    A more efficient use of bandwidth can be achieved allowing many physical groups to use the same
network infrastructure.
C.    A more efficient use of bandwidth can be achieved allowing many logical networks to use the same
network infrastructure.
D.    Broadcast storms can be mitigated by increasing the number of broadcast domains, thus reducing
their size.
E.    Broadcast storms can be mitigated by decreasing the number of broadcast domains, thus increasing
their size.
F.    VLANs make it easier for IT staff to configure new logical groups, because the VLANs all belong to
the same broadcast domain.
G.    Port-based VLANs increase switch-port use efficiency, thanks to 802.1Q trunks.

Answer: ACD
Explanation:
Benefits of VLANs
VLAN is a network structure which allows users to communicate while in different locations by sharing one multicast domain and a single broadcast. They provide numerous networking benefits and have become popular in the market. For instance, it helps reduce administrative costs when users are geographically dispersed.
1. Inexpensive
The popularity of VLANs is due to the fact that changes, adds, and moves can be attained simply by making necessary configurations on the VLAN port. Time-consuming, re-addressing, and host reconfigurations is now a thing of the past, because network configuration can be made at ease when need arises.
2. Better management
A VLAN typically solve the scalability issues that exist in a large network by breaking the main domain into several VLAN groups or smaller broadcast configurations, thereby encourage better control of multicast traffic as well as broadcast domains.
3. Improves network security
High-security can be positioned in different VLAN groups to ensure that non-members cannot receive their broadcasts. On the other hand, a router is added and workgroups relocated into centralized locations.
4. Enhances performance
A more efficient use of bandwidth can be achieved allowing many logical networks to use the same network infrastructure.
5. Segment multiple networks
VLANs are typically used to achieve multiple purposes. They are popularly used to reduce broadcast traffic. Each VLAN creates a separate, smaller broadcast domain.
6. Better administration
VLANs facilitate grouping of multiple geographical stations. When VLAN users move to another physical location, the network does not have to be configured.

QUESTION 25
Which IEEE standard protocol is initiated as a result of successful DTP completion in a switch over Fast Ethernet?

A.    802.3ad
B.    802.1w
C.    802.1D
D.    802.1Q

Answer: D
Explanation:
Dynamic Trunking Protocol (DTP) is a Cisco proprietary protocol for negotiating trunking on a link between two devices and for negotiating the type of trunking encapsulation (802.1Q) to be used.

QUESTION 26
Which of the following are benefits of VLANs? (Choose three.)

A.    They increase the size of collision domains.
B.    They allow logical grouping of users by function.
C.    They can enhance network security.
D.    They increase the size of broadcast domains while decreasing the number of collision domains.
E.    They increase the number of broadcast domains while decreasing the size of the broadcast domains.
F.    They simplify switch administration.

Answer: BCE
Explanation:
When using VLAN the number and size of collision domains remain the same -> VLANs allow to group users by function, not by location or geography -> . VLANs help minimize the incorrect configuration of VLANs so it enhances the security of the network -> .
VLAN increases the size of broadcast domains but does not decrease the number of collision domains ->
VLANs increase the number of broadcast domains while decreasing the size of the broadcast domains which increase the utilization of the links. It is also a big advantage of VLAN -> . VLANs are useful but they are more complex and need more administration ->

QUESTION 27
Refer to the exhibit. A technician has installed SwitchB and needs to configure it for remote access from the management workstation connected to SwitchA . Which set of commands is required to accomplish this task?
271

A.    SwitchB(config)# interface FastEthernet 0/1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown
B.    SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# ip default-gateway 192.168.8.254 255.255.255.0
SwitchB(config-if)# no shutdown
C.    SwitchB(config)# ip default-gateway 192.168.8.254
SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown
D.    SwitchB(config)# ip default-network 192.168.8.254
SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown
E.    SwitchB(config)# ip route 192.168.8.254 255.255.255.0
SwitchB(config)# interface FastEthernet 0/1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown

Answer: C
Explanation:
To remote access to SwitchB, it must have a management IP address on a VLAN on that switch. Traditionally, we often use VLAN 1 as the management VLAN (but in fact it is not secure). In the exhibit, we can recognize that the Management Workstation is in a different subnet from the SwitchB. For intersubnetwork communication to occur, you must configure at least one default gateway. This default gateway is used to forward traffic originating from the switch only, not to forward traffic sent by devices connected to the switch.

QUESTION 28
In an Ethernet network, under what two scenarios can devices transmit? (Choose two.)

A.    when they receive a special token
B.    when there is a carrier
C.    when they detect no other devices are sending
D.    when the medium is idle
E.    when the server grants access

Answer: CD
Explanation:
Ethernet network is a shared environment so all devices have the right to access to the medium. If more than one device transmits simultaneously, the signals collide and can not reach the destination.
If a device detects another device is sending, it will wait for a specified amount of time before attempting to transmit.
When there is no traffic detected, a device will transmit its message. While this transmission is occurring, the device continues to listen for traffic or collisions on the LAN. After the message is sent, the device returns to its default listening mode.

QUESTION 29
Which two states are the port states when RSTP has converged? (Choose two.)

A.    discarding
B.    listening
C.    learning
D.    forwarding
E.    disabled

Answer: AD
Explanation:
http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml #states

QUESTION 30
Which two commands can be used to verify a trunk link configuration status on a given Cisco switch interface? (Choose two.)

A.    show interface trunk
B.    show interface interface
C.    show ip interface brief
D.    show interface vlan
E.    show interface switchport

Answer: AE

QUESTION 31
Which of the following statements describe the network shown in the graphic? (Choose two.)
311

A.    There are two broadcast domains in the network.
B.    There are four broadcast domains in the network.
C.    There are six broadcast domains in the network.
D.    There are four collision domains in the network.
E.    There are five collision domains in the network.
F.    There are seven collision domains in the network.

Answer: AF
Explanation:
Only router can break up broadcast domains so in the exhibit there are 2 broadcast domains: from e0 interface to the left is a broadcast domain and from e1 interface to the right is another broadcast domain ->.
Both router and switch can break up collision domains so there is only 1 collision domain on the left of the router (because hub doesn’t break up collision domain) and there are 6 collision domains on the right of the router (1 collision domain from e1 interface to the switch + 5 collision domains for 5 PCs in Production) ->

QUESTION 32
Which command enables RSTP on a switch?

A.    spanning-tree uplinkfast
B.    spanning-tree mode rapid-pvst
C.    spanning-tree backbonefast
D.    spanning-tree mode mst

Answer: B
Explanation:
Ethernet network is a shared environment so all devices have the right to access to the medium. If more than one device transmits simultaneously, the signals collide and can not reach the destination.
If a device detects another device is sending, it will wait for a specified amount of time before attempting to transmit.
When there is no traffic detected, a device will transmit its message. While this transmission is occurring, the device continues to listen for traffic or collisions on the LAN. After the message is sent, the device returns to its default listening mode.

QUESTION 33
Refer to the exhibit. All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?
331

A.    The access link needs to be configured in multiple VLANs.
B.    The link between the switches is configured in the wrong VLAN.
C.    The link between the switches needs to be configured as a trunk.
D.    VTP is not configured to carry VLAN information between the switches.
E.    Switch IP addresses must be configured in order for traffic to be forwarded between the switches.

Answer: C
Explanation:
In order to pass traffic from VLANs on different switches, the connections between the switches must be configured as trunk ports.

QUESTION 34
What is the function of the command switchport trunk native vlan 999 on a Cisco Catalyst switch?

A.    It creates a VLAN 999 interface.
B.    It designates VLAN 999 for untagged traffic.
C.    It blocks VLAN 999 traffic from passing on the trunk.
D.    It designates VLAN 999 as the default for all unknown tagged traffic.

Answer: B
Explanation:
Configuring the Native VLAN for Untagged Traffic
A trunk port configured with 802.1Q tagging can receive both tagged and untagged traffic. By default, the switch forwards untagged traffic in the native VLAN configured for the port. The native VLAN is VLAN 1 by default.

QUESTION 35
Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the reason that interface FastEthernet 0/10 is not the root port for VLAN 2?
351

A.    This switch has more than one interface connected to the root network segment in VLAN 2.
B.    This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.
C.    This switch interface has a higher path cost to the root bridge than another in the topology.
D.    This switch has a lower bridge ID for VLAN 2 than the elected designated switch.

Answer: C
Explanation:
Since the port is in the blocked status, we must assume that there is a shorter path to the root bridge elsewhere.

QUESTION 36
Why will a switch never learn a broadcast address?

A.    Broadcasts only use network layer addressing.
B.    A broadcast frame is never forwarded by a switch.
C.    A broadcast address will never be the source address of a frame.
D.    Broadcast addresses use an incorrect format for the switching table.
E.    Broadcast frames are never sent to switches.

Answer: C
Explanation:
Switches dynamically learn MAC addresses based on the source MAC addresses that it sees, and since a broadcast is never the source, it will never learn the broadcast address.

QUESTION 37
Refer to the exhibit. Why has this switch not been elected the root bridge for VLAN1?
371

A.    It has more than one interface that is connected to the root network segment.
B.    It is running RSTP while the elected root bridge is running 802.1d spanning tree.
C.    It has a higher MAC address than the elected root bridge.
D.    It has a higher bridge ID than the elected root bridge.

Answer: D
Explanation:
The root bridge is determined by the lowest bridge ID, and this switch has a bridge ID priority of 32768, which is higher than the roots priority of 20481.

QUESTION 38
Which two link protocols are used to carry multiple VLANs over a single link? (Choose two.)

A.    VTP
B.    802.1q
C.    IGP
D.    ISL
E.    802.3u

Answer: BD
Explanation:
Cisco switches can use two different encapsulation types for trunks, the industry standard 802.1q or the Cisco proprietary ISL. Generally, most network engineers prefer to use 802.1q since it is standards based and will interoperate with other vendors.

QUESTION 39
Assuming the default switch configuration, which VLAN range can be added, modified, and removed on a Cisco switch?

A.    1 through 1001
B.    2 through 1001
C.    1 through 1002
D.    2 through 1005

Answer: B
Explanation:
VLAN 1 is the default VLAN on Cisco switch. It always exists and can not be added, modified or removed.
VLANs 1002-1005 are default VLANs for FDDI & Token Ring and they can’t be deleted or used for Ethernet.

QUESTION 40
Which statement about VLAN operation on Cisco Catalyst switches is true?

A.    When a packet is received from an 802.1Q trunk, the VLAN ID can be determined from the source
MAC address and the MAC address table.
B.    Unknown unicast frames are retransmitted only to the ports that belong to the same VLAN.
C.    Broadcast and multicast frames are retransmitted to ports that are configured on different VLAN.
D.    Ports between switches should be configured in access mode so that VLANs can span across the ports.

Answer: B
Explanation:
Each VLAN resides in its own broadcast domain, so incoming frames with unknown destinations are only transmitted to ports that reside in the same VLAN as the incoming frame.

Once there are some changes on 200-125 exam questions, we will update the study materials timely to make sure that our customer can download the latest edition.

200-125 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDbnNGVlNHTzJjcWc

2016 Cisco 200-125 exam dumps (All 545 Q&As) from Lead2pass:

http://www.lead2pass.com/200-125.html [100% Exam Pass Guaranteed]

Lead2pass Testking Pass4sure Actualtests Others
$99.99 $124.99 $125.99 $189 $29.99-$49.99
Up-to-Dated
Real Questions
Error Correction
Printable PDF
Premium VCE
VCE Simulator
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back